User Contributed                                           MET/CAL PROCEDURE
=============================================================================
INSTRUMENT:            West 1411:Temp Indicator
DATE:                  17-Mar-97
AUTHOR:                User Contributed
REVISION:
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       4
NUMBER OF LINES:       85
STANDARD:              Ectron 1120-1
STANDARD:              Ectron 1120
=============================================================================
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
# Equipment #25-5493-3 and 25-5493-4 Equip. Type: West 1411 Temp Indicator
# Notes:                                          Controller.
#
# Review Approval:_____________________________ Release Date:____/___/____


  1.001  ASK+                                      M   X
  1.002  ASK-   R     N              P                            F        W
  1.003  OPBR         Are you using the Ectron 1120 EQ #701-064?
  1.004  JMPT         1.007
  1.005  STD          Ectron 1120-1
  1.006  JMP          1.008
  1.007  STD          Ectron 1120
  1.008  RSLT         =Accuracy: ñ2.0% of Full Scale or ñ16øF
  1.009  RSLT         =
  1.010  RSLT         =Reference Documents: Manufacturers manual.
  1.011  RSLT         =
  1.012  HEAD         Setup
  1.013  DISP         Connect the proper thermocouple extension wire
  1.013  DISP         between the UUT and the Ectron.
  1.014  DISP         Use the Ectron to drive the UUT to the nominal
  1.014  DISP         value. You will enter the STD indicated value.

  1.015  HEAD         Type J T/C 80øF
  1.016  DISP
  1.016  DISP         ÿ        Drive the UUT to indicate 80øF...
  1.017  ACC          80.00øF        0.018%
  1.018  MEMI         Enter the STD indicated temperature.
  1.019  MEMC         øF             16.00U
#!          Test Tol 16, Sys Tol 0.0144, TUR 1111.11 (>= 4.00).

  2.001  HEAD         Type J T/C 400øF
  2.002  DISP
  2.002  DISP         ÿ        Drive the UUT to indicate 400øF...
  2.003  ACC          400.00øF       0.018%
  2.004  MEMI         Enter the UUT indicated temperature.
  2.005  MEMC         øF             16.00U
#!          Test Tol 16, Sys Tol 0.072, TUR 222.222 (>= 4.00).

  3.001  HEAD         Type J T/C 720øF
  3.002  DISP
  3.002  DISP         ÿ        Drive the UUT to indicate 720øF...
  3.003  ACC          720.00øF       0.018%
  3.004  MEMI         Enter the UUT indicated temperature.
  3.005  MEMC         øF             16.00U
#!          Test Tol 16, Sys Tol 0.1296, TUR 123.457 (>= 4.00).

  4.001  HEAD         {Trip Point Check}
  4.002  RSLT         =
  4.003  MEMI         Enter the trip point setting.
  4.004  MEME                                                     >1
  4.005  DISP         Drive the ECTRON up to the trip point and note the
  4.005  DISP         Ectron indicated value when the system trips.
  4.006  MEMI         Enter the Ectron indicated value where the UUT tripped.
  4.007  MATH         mem1=m[1]
  4.008  OPBR         The Actual trip point was [mem]øF
  4.008  OPBR         The Setting was [mem1]øF
  4.008  OPBR
  4.008  OPBR         Is this acceptable?
  4.009  JMPF         4.012
  4.010  RSLT         =Trip point check PASSED.
  4.011  JMP          4.013
  4.012  RSLT         =Trip point check FAILED. Maint. Required.

  4.013  HEAD
  4.014  DISP         ÿ     P R O C E D U R E
  4.014  DISP         ÿ     ÿ   COMPLETED!
#! T.U.R.s less than 4.00:                  0
#! T.U.R.s estimated using RANGE value:     0
#! T.U.R.s not calculated (ASK- U):         0
#! T.U.R.s not computable at compile time:  0
#! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.